Product Center
Home » oxy acetylene machine gas cutting nozzles diagram instructions
  • Oxy Acetylene Cutting Nozzles | ANM Nozzles from Adams Gas

    To browse a diverse range of oxy acetylene single and two piece cutting nozzles, visit Adams Gas online today. We supply an arraty of nozzles to suit your needs.

  • TurboTorch - Total Control

    Victor dominates as the most demanded product in oxy acetylene gas apparatus. For the first time, the TurboTorch For the first time, the TurboTorch catalog features an extended offering of genuine Victor gas apparatus including outfits, handles, cutting attachments,

  • Safe Operating Procedure OXY ACETYLENE SET

    Purge and check for constant acetylene/fuel gas flow. • Open the acetylene/fuel blowpipe valve for 2 seconds and check the delivery gauge. • If necessary re-adjust the acetylene regulator to achieve a 70kPa pressure. •

  • OXY-FUEL WELDING, HEATING AND CUTTING - Gas ...

    In cutting steel, a neutral oxy-fuel flame (Figure 4), is used for preheating. When possible the cut is started at the edge of the workpiece (Figure 7.2). Hold the cutting torch lightly but steadily, so that the ends of the preheating flame cones are about 1/8 inch above the surface of the metal.

  • Medium-Duty Oxy-Acetylene Cutting and Welding Outfit …

    Medium-Duty Oxy-Acetylene Cutting and Welding Outfit 770 502 www.HobartWelders.com Description OM-251 341A 2011−08 File: Accessory Accessory Processes Oxy-Fuel Welding and Cutting Hobart is registered to the ISO

  • Introduction to Oxy-Acetylene Welding - SAIC

    Adjust acetylene to form feather shaped flame. Continue to add oxygen until neutral flame is established. If there is too much acetylene, flame breaks away from the …

  • OXY-ACETYLENE GAS CUTTING PLANT SETTING || WELDING ALL TIPS ...

    Hello friends. This is video is a knowledge for welding tips. . follow me on Instagram... https://instagram.com/faiz___siddiqui?utm_source=ig_profile_share&i...

  • Module 2 Thermal Processes - eCollege

    There are seven Units in Module 2. Unit 1 focuses on Introduction to Thermal Process and safety, Unit 2; Introduction to Oxy-acetylene welding, Unit 3; Manual Metal Arc welding, Unit 4; Metal Active Gas welding, Unit 5; Tungsten Active Gas welding, Unit 6; Oxy-fuel cutting and Unit 7 Plasma arc cutting.

  • FACTORS AFFECTING QUALITY IN OXY-FUEL CUTTING

    What is top Quality in Oxy-fuel cutting? 1. Square top corner (with minimum radius), 2. Cut face flat top to bottom (no undercut), 3. Cut face square with respect to top surface, . …

  • Acetylene Nozzles Or More Accurately Oxy Acetylene Nozzles

    ANME-10 Heavy Duty Acetylene Cutting Nozzle Large Sizes. Oxy / Acetylene Heavy Duty Cutting Nozzle 10 Pre-Heat Flames - 500mm Capacity. £14.95. £24.87. (Inc VAT £17.94)

  • OXY-FUEL WELDING, HEATING AND CUTTING - CONCOA - Gas Pressure ...

    Oxy-Fuel Gas Cutting and Welding Operation of oxy-fuel torches involves oxygen and flammable gases under pressure, open flames, flying slag and hot metal, meatl fumes and combustion products. Follow the precautions in this SAFETY section and those throughout this manual for your personal safety and the safety of people near the equipment.

  • Cutting Tips – AIRCO / Concoa Acetylene - Oxygen

    • Hand and machine cutting, two piece • Fits CA2450, CA1060, CAN 1060, ST, SST, STN machine torches 3V-FS-68, 60, 56, 52, 49 • Medium preheat • Hand cutting, two piece W W-1 Cutting Tips – Victor Acetylene - Oxygen Propane - Natural Gas Welding Tips – Victor Acetylene - Oxygen Heating Tips – Victor Acetylene or Hydrogen - Oxygen ...

  • Welding Supplies | Welding Machines | Plasma Cutting ...

    Victor dominates as the most demanded product in oxy acetylene gas apparatus. For the first time, the TurboTorch For the first time, the TurboTorch catalog features an extended offering of genuine Victor gas apparatus including outfits, handles, cutting attachments,

  • How does the oxyacetylene cutting process work?

    A jet of pure oxygen is then directed into the preheated area instigating a vigorous exothermic chemical reaction between the oxygen and the metal to form iron oxide or slag. The oxygen jet blows away the slag enabling the jet to pierce through the material and continue to cut through the material. Fig.1. Diagram of oxyacetylene cutting process

  • Oxyfuel Cutting - Process and Fuel Gases - TWI

    Oxy-fuel cutting is a thermal cutting process that uses oxygen and fuel gas (such as acetylene, propane, MAPP, propylene and natural gas) to cut through materials. The oxyfuel process is the most widely applied industrial thermal cutting process because it can cut thicknesses from 0.5mm to 250mm, the equipment is low cost and can be used ...

  • How To Use Oxy Acetylene Torch: Basics For Beginners

    Sep 24, 2020 · Oxy-Acetylene Torch Use and Safety: Burning acetylene gas is the key point to produce much heat or energy and the temperature could be 5620 degrees. So, this torch may be easy to use, but it can burn and explode if you can’t handle it properly. Along with the basic torch outfit, this single piece of equipment is popular in the welder community.

  • Guidelines for Gas Welding and Cutting - BOC

    The oxy-acetylene flame produces an intense bright light that causes discomfort and possible injury to the eyes. In order to comfortably and safely see the flame when welding or cutting, welding goggles must be worn. various processes: Shade 4 – Oxy-cutting and gouging. – Flame cleaning. – Braze welding of light copper and steel.

  • Straight Line Cutter

    2. INTRODUCTION. Read this instruction manual thoroughly to ensure correct, safe, and effective use of the machine. Co-operation between colleagues in the workplace is essential for safe, smooth operation. SAFETY PRECAUTIONS. This product is designed to be safe, but it can cause serious accidents if not operated correctly.

  • CUTTING AND WELDING GAS CONTROL EQUIPMENT

    when oxy-acetylene cutting and welding methods were first invented. GCE itself was formed in 1987 through the merging of two gas equipment activities from the world’s leading industrial gas companies into one entity. The GCE ...

  • Oxy-fuel welding and cutting - Wikipedia

    Oxy-fuel welding (commonly called oxyacetylene welding, oxy welding, or gas welding in the United States) and oxy-fuel cutting are processes that use fuel gases (or liquid fuels such as gasoline) and oxygen to weld or cut metals. French engineers Edmond Fouché and Charles Picard became the first to develop oxygen- acetylene welding in 1903.

  • Medium-Duty Oxy-Acetylene Cutting and Welding Outfit 770 502

    Keep torch flame or sparks away from cylinder, regulator, and gas hose. Use only acetylene or propane gas and oxygen with this equip-ment. Do not use acetylene above 15 psi (103 kPa) static. Check oxy-fuel system for leaks with an approved leak detection solution or leak detector. Remove all flammables within 35 ft (10.7 m) of the welding or cut-

  • Where can I find medium duty oxy acetylene?

    Medium-Duty Oxy-Acetylene Cutting and Welding Outfit 770 502 Medium-Duty Oxy-Acetylene Cutting and Welding Outfit 770 502 www.HobartWelders.com Description OM-251 341A2011−08 File: Accessory Accessory Processes Oxy-Fuel Welding and Cutting Hobart is registered to the ISO 9001 Quality System Standard. TABLE OF CONTENTS

  • Heavy Duty Cutting Kit Oxy-Acetylene - HSS

    Cutting Kit Oxy-Acetylene A portable cutting kit capable of cutting up to 300mm thickness. Remove the cap from the cutting torch’s head nut Operating & Safety Guide HW035 followed by the nut itself. Fit the required nozzle (see table), screw the head nut back in place and tighten up with the spanner provided.

  • : oxy acetylene tips

    2 Tip Cleaner Sets for Cleaning Welding Cutting Nozzles/Tips, Gas Orifices, Engine Carburetors, Sprinklers, and Shower Heads Professional Large and Small 13 Wire Oxy-Acetylene. 4.6 out of 5 stars. 248. $7.99.

  • Guidelines for Gas Welding and Cutting - BOC

    12.0 Gas Cutting 40 13.0 Oxy-fuel Cutting Procedures 42 13.1 Cutting Attachment Operation 42 13.2 Setting Up 43 13.3 Lighting Up 44 13.4 Closing Down 45 14.0 Oxy-acetylene Cutting …

  • How do you cut metal with oxy acetylene torch?

    Squeeze the lever to do that. Because of this action, the metal starts to cut. If it’s not cutting yet, then preheat it. When you notice the flame is cutting the metal, then begin to move the torch to get the job done following the right coordination. After finishing the cutting session, close all the valves.

  • Gas Cutting Equipment | Oxygen & Acetylene | Adendorff ...

    M&B MB90 Heavy Duty Oxygen Gas Regulator. R 695.00. SKU: EOXYGA-001. Gas Cutting Equipment. MAC AFRIC Oxygen & Acetylene Cutting Torch (Semi Heavy Duty) R 795.00. SKU: EOXYAC-004. Gas Cutting Equipment. MAC AFRIC Acetylene Hose 8 mm x 6 m.

  • Gas Cutting Nozzles For Welding, Available Online at Gas UK

    The gas cutting nozzles that we supply at Gas UK are guaranteed to last, ensuring that you get more out of them. The cutting nozzle for welding can create a smooth passage for gas to pass through, ensuring that it’s efficient. All of our gas cutting nozzles for welding are made to be lightweight, making it more convenient for you to work with.

  • Koike oxy fuel gas cutting nozzles - WB Alloys

    Machine cutting nozzles Cutting nozzle 102 D5 High speed cutting nozzle mix Acetylene Cutting range Description Article no. 0-5 mm 00 80201 5-10 mm 0 80202 10-15 mm 1 80203 15-30 mm 2 80204 30-40 mm 3 80205 40-50 mm 4 80206 50-100 mm 5 80207 100-150 mm 6 80208 150-250 mm 7 80209 250-300 mm 8 80210 Cutting nozzle 102 D7 High speed cutting nozzle ...

  • INSTRUCTION MANUAL - Welding, Brazing, Heating, Cutting ...

    Gas Welding , Brazing & Cutting Basic Gas Welding Procedures Gas Welding. Gas welding is a method of joining similar metals by heating the adjacent surfaces to the melting point with an oxy-acetylene flame, and allowing the two parts to fuse together, with a filler metal being required on materials 5mm thick or more.

  • FACTORS AFFECTING QUALITY IN OXY-FUEL CUTTING

    performances below 10 psi. See “Torch and Cutting Nozzles” section beginning on Page 15. 8. Do not arbitrarily change fuel gas type without consulting present supplier to be sure correct torch and nozzles are being used. See

  • Setup and Shutdown Procedure for Oxy- fuel Cutting Torch

    Lighting the Oxy-fuel torch 1. Turn the acetylene knob on the cutting torch about a quarter of a turn and light the acetylene. Make sure that the flame is up against the tip. If you light up the tip and the flame is away from the tip, decrease the acetylene pressure and let the flame come back against the tip. (Use your safety equipment ...

  • Oxy-Acetylene Cutting Processes | Metallurgy

    ADVERTISEMENTS: Subject-Matter of Oxy-Acetylene Cutting Process: In modern steel-age the steel-makers cut Iron and Steel by oxy-acetylene, oxy-hydrogen, oxy- propane, oxy-natural gas cutting blowpipes easily, speedily, and cleanly. Cutting of metals by means of flame has many advantages over other methods, specially when the metal is of irregular shape. When using oxy-acetylene a special torch

  • Comet Blowpipes Cutting Attachments and Consumables

    COMET Type 44 Cutting Nozzles 13 COLT Type 90 Cutting Nozzles 14 3-Seat Cutting Nozzles (Machine Cutting) 15 Welding & Heating Tips 16 COMET Oxy/Acetylene Welding Tips 16 COMET Oxy/LP Gas Brazing Tips 16

  • Gas Welding Equipment's (With Diagram)

    2016/06/02 · It consists of three parts: (1) Pressure spring; (2) Diaphragm; (3) Valve. ADVERTISEMENTS: Other parts are wing-nut connection, safety valve, outlet valve and connection and two gas pressure gauges (container pressure and working pressure). Oxygen and acetylene regulators are similar in construction.

  • STANDARD SPEED CUTTING NOZZLES – OXY / ACETYLENE ORDERING ...

    with both hand cutting and profile machine cutting. • No flame blow off (Type 44) – Slotted preheat ports cause a turbulence in the gas flow enabling the flame to hang on to the nozzle. • Tapered gas passage tip - A small taper in the end of the nozzle alters the expansion of the oxygen jet stream. This, combined

  • INSTRUCTIONS for C-58 MACHINE CUTTING TORCHES

    INSTRUCTIONS for F-5884-V June, 2009 C-58 MACHINE CUTTING TORCHES OPERATING INSTRUCTIONS CONNECTING 1. Attach regulators to the oxygen and fuel gas cylinders. Fol-low all instructions supplied with the

  • Oxygen And Acetylene Use And Safety - ia

    What Is Acetylene? •Auto-ignition temperature is 763o - 824o F. This means if acetylene reaches 30 psi in a free state, it can explode by itself without a spark or flame being present. • Has a burning temperature of 4,600o F. 5,700 o F when burned with oxygen. • Remember…. acetylene is a very dangerous gas.

  • Oxy-Acetylene Straight Line Cutting Machine 230V - Welding ...

    Portable, single torch, automatic straight-line cutting machine 230volt. Specifications: Available in models to suit 115v and 230v input power supply. Supplied with a 2 x 1.2M length of distortion-proof steel track (extra lengths also available) A selection of cutting nozzles. Cuts straight lines, circles (20cm-2m radius) and bevels on 5mm-50mm ...

  • Oxy-Fuel Torch Tip/Nozzle Design and Selection

    Part 1 of a 2 part series. When designing or selecting an oxy-fuel machine torch cutting nozzle/tip one must consider several factors. The following are several, but not all, items to be considered 1) thickness of the steel to be cut, 2) type cutting bore (cylindrical bore or high speed/divergent bore), 3) preheat gas to be used, 4) type cutting to be conducted (shape cutting, bevel cutting ...